Name: 2K Epoxy Bonding Primer – 750 ml Primer for Concrete &amp; Garage
Brand: PLID
SKU: 129345
Availability: InStock

Description

Item description

Article No. S0R F50 1Z

Colorless, water-based 2K epoxy adhesion promoter for mineral substrates such as concrete and garage floors, high adhesion strength.
Container: 580 ml base + 170 ml hardener, filled in the correct ratio, mix completely, stir thoroughly for at least 3 minutes.
Economical: Consumption approx. 0.15–0.2 l/m², sufficient for approx. 5 m² per coat. Apply thinly and evenly with a brush or roller.
Fast drying: dust-dry after approx. 4 hours, walkable after approx. 12 hours, recoatable after 12–48 hours, pot life approx. 60 minutes at 20 °C.
High adhesion ensures a durable floor coating, prevents peeling and provides a resistant surface.

Hazard warnings

H315: Causes skin irritation. H317: May cause an allergic skin reaction. H319: Causes serious eye irritation.

Safety instructions

P101: If medical advice is needed, have product container or label at hand. P102: Keep out of reach of children. P103: Read all instructions carefully and follow them. P261: Avoid breathing vapors. P280: Wear protective gloves, protective clothing, eye protection, face protection. P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P332+P313: If skin irritation occurs: Get medical advice/attention. P337+P313: If eye irritation persists: Get medical advice/attention.

Plid 2K Epoxy Bonding Agent is a colorless, water-based, two-component epoxy resin primer for mineral substrates such as concrete and garage floors. It ensures optimal adhesion between the substrate and the floor coating, dries clear, and offers high bond strength.

Packaging and mixture:

Contents: 750 ml (580 ml base + 170 ml hardener)
Add the hardener completely to the base and mix thoroughly for at least 3 minutes until a milky emulsion is formed.
Do not mix partial quantities

Consumption and yield:

Approximately 0.15–0.2 l/m² depending on the substrate
Sufficient for approximately 5 m² with one coat.
Apply thinly and evenly with a brush or short-pile roller.

Drying and processing:

Completely dry after approximately 4 hours at 20 °C
Walkable after approx. 12 hours, reworkable after 12–48 hours
Potting time: approx. 60 minutes at 20 °C
Processing at +10 to +30 °C, relative humidity below 80%

Advantages:

High adhesion for durable floor coatings
Easy to use thanks to pre-packaged components
Economical consumption and quick re-entry
Made in Germany

Details

Product details
Contents	0.75 l
Suitable substrates	Concrete and garage floors as well as other mineral substrates
Subsurface conditions	Clean, dry, load-bearing – no loose parts. Dust-free – ideally cleaned with an industrial vacuum cleaner. Free of separating substances – e.g., thoroughly remove oil and grease. Repair defects – with floor filler or rapid-setting cement. Remove cement slurry or silicate layers – by shot blasting or grinding. Tensile adhesion strength – at least 1.5 N/mm².
Characteristics	colorless, water-based, easy to use
Scope of delivery	Base (580 ml) + Hardener (170 ml)
Yield per liter	6 m²
Mixing ratio	Mix base (580 ml) + hardener (170 ml).
Minimum processing temperature	10 °C
Maximum processing temperature	30 °C
Drying time	12 hours

Measurements
Weight	2.5 kg

Notes
Processing instructions	Mixing components: Add the hardener completely to the base and stir thoroughly for at least 3 minutes (drill + mixer recommended) until a milky emulsion is formed. Pot life: approx. 60 minutes at 20 °C (batch size 0.75 l); shorter at higher temperatures, longer at lower temperatures. Application: Apply a thin, even coat with a brush or short-pile roller. Drying: Dust-dry after approx. 4 hours, walkable after approx. 12 hours, recoatable after 12–48 hours. Working conditions: +10 to +30 °C (air & substrate), relative humidity < 80%. Ventilation: Ensure good ventilation during the drying phase. Tool cleaning: Clean with water immediately after use; perform intermediate cleaning of tools during longer work breaks.
Hazard warnings	H315: Causes skin irritation. H317: May cause an allergic skin reaction. H319: Causes serious eye irritation.
Safety instructions	P101: If medical advice is needed, have product container or label at hand. P102: Keep out of reach of children. P103: Read all instructions carefully and follow them. P261: Avoid breathing vapors. P280: Wear protective gloves, protective clothing, eye protection, face protection. P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P332+P313: If skin irritation occurs: Get medical advice/attention. P337+P313: If eye irritation persists: Get medical advice/attention.
Signal word	Danger

Reviews

There are no reviews yet.

Be the first to review “2K Epoxy Bonding Primer – 750 ml Primer for Concrete & Garage”

Clothings

Dresses

Accessories

Clothings

Corporate

Accessories

GIRLS FASHION

BOYS FASHION

BABY FASHION

Scooters

Clothings

Dresses

Accessories

Clothings

Corporate

Accessories

GIRLS FASHION

BOYS FASHION

BABY FASHION

Scooters

Shop

2K Epoxy Bonding Primer – 750 ml Primer for Concrete & Garage

Description

Item description

Hazard warnings

Safety instructions

Details

Reviews

Related products